Category 3 or better shielded twisted-pair (STP) or unshielded twisted-pair (UTP) can be used. Use only dedicated wire pairs (such as blue/white & white/blue, orange/white & white/orange) for the active pins. The two RJ-45 active pairs in a T1/E1 network are pins 1 & 2 and pins 4 & 5. Refer to the user-guide ( NID) to set the DIP switches (T1 or E1 mode) as required. If a circuit is presented on coaxial connectors, always use a balun with a matching impedance, eg: 75 to 120 ohm.ĭS1 - T1/E1 converters must be used in pairs, one on each end of the fiber link. The RJ45 side uses the standard pairs: 1 & 2, and 4 & 5.
A G.703 Balun is a bi-directional passive device (transformer) that converts unbalanced (75 ohm, BNC) to balanced (120 ohm, RJ45) signals. RJ48 connector will prevent it from plugging into an RJ45 jack.Īn E1 maybe presented on two coaxial connectors (eg, BNC's), one each for TX and RX. Note: An RJ45 connector will fit an RJ48 jack, but the key on an
Note the improvised loopback adapter in this picture! With a 568B cable, jumper the Orange to Blue pair. DB-15 (T1) - Loop pin 1 to pin 3, and pin 9 to pin 11.DB-9 (E1) - Loop pin 2 to pin 6, and pin 3 to pin 7.You may need to reverse the TX / RX pairs - or swap orange & blue with T-568B ( 568A or 568B). Use the following adapter configuration with an E1, DB-9 end on the PBX (to NTCK45AA on J5). The picture also shows an improvised RJ45 loopback adapter used for testing (blue and orange pairs looped)! Large systems (51C/61C/81C) use a DB-9 (E1), or DB-15 (T1) connector, located at the rear of a network shelf. If the circuit doesn't go green, swap the TX/RX pairs: If neither are available, make the termination directly on the MDF block associated with the card slot using the following pinout. The NTBK65 is a replacement to the NTBK04 cable assembly. The following table shows the NTBK65 adaptor signal pin out: Be prepared to swap these, to switch the TX / RX pairs. An RJ-45 connector will fit an RJ-48 jack, but the key on an RJ-48 connector will prevent it from plugging into an RJ-45 jack.Ī standard RJ-45 ethernet cable (568B) works, but note the active pairs are orange and blue, not orange/green. If the circuit doesn't go green, just swap the TX/RX pairs. If you can't find an NTBK65 UDT RJ48C breakout adaptor (right), use pairs 23 (TX) and 24 (RX) on the MDF.
Media Gateways (and Option 11's) can use an NTBK04 cable, NTBK65 adapter, or a direct MDF connection. A single direct CAT5/6 cable is always preferred.
#Rj45 loopback connector Patch
Ethernet accessories (eg, patch panels) may either not work or cause problems. Note: When using RJ-45's, remember it isn't ethernet! The active pairs in a T1/E1 network are pins 1 & 2 and pins 4 & 5, not 1 & 2 and 3 & 6. * CSU/DSU = Channel Service Unit/Data Service Unit, eg, the PTT modem. The following table shows the pinouts for each: A Yellow "Far End Alarm" (FEA) indicates the local TX pair is open (a yellow alarm is "received").Ī circuit can be presented on a DB-9 (E1), DB-15 (T1), or RJ48/RJ45.A Red "Near End Alarm" (NEA) indicates a local cabling problem, with the RX (or both) pairs open.It can use a number of different connection methods depending upon the service, provider, equipment, and location:Ī TX pair will generally connect to a RX pair, but be prepared to experiment a little (and/or swap/crossover the pairs). A 2 pair connection (TX/RX) between the service providers CSU/DSU (Channel Service Unit/Data Service Unit) and the customers PBX.
0 kommentar(er)
